繁體版     English

E-mail:susan@brakepad.cn     +86-532-66736778

Welcome

News

How Disc Brake Conversion Works

[Catalog:News] [Date:2020-2-19] [Hits:] [Return]

Making your ride stop better is hardly the coolest way to soup it up. But whether you're a tuner-car enthusiast looking to make your WRX drift-ready or an average Joe looking to tweak the safety and performance of your beloved '68 F-150, a disc brake conversion is actually the first modification you should consider.

There are many good reasons to ditch your old-fashioned drum brakes for discs. Drum brakes can be troublesome; they're easily damaged by heat, moisture and debris, they offer less-than-optimal stopping power, and they often need regular adjustment.

The obvious candidates for disc brake conversions are pre-1970 vehicles, since disc brakes didn't become standard until the '70s. Chrysler introduced standard disc brakes in the 1950s, but this innovation didn't catch on until the mid-1960s, when power brake systems, which made disc brakes easier to operate, hit the market. But even most modern cars and trucks still come standard with drums on rear wheels. Rear drums have stuck around mostly because they're cheaper than disc brakes, and since a car's front brakes do 70 percent of the work, rear brake performance can be sacrificed for cost. [Source: Professional Mechanics Online]

In this ­article, we'll look at the basics of brake conversion, including the tools you'll need to do the job yourself, the difference between front and rear conversions, and the kits available to save yourself a trip to the junkyard.

If you know your calipers from your spindles, ­you probably have the expertise to do the brake conversion yourself. But do you have all the tools you need? Read on to find out.

Since you're either savvy enough or foolhardy enough to attempt a brake conversion yourself, your garage is probably already stocked with all the tools you'll need to assemble your disc brakes. But putting your new brakes on is not going to be the hard part. Taking off your old brakes will probably pose the biggest challenge.

Maybe your bolts haven't fused and rusted, and maybe all the lubrication has managed to not dry up and blow away. If you happen to be that lucky, then a socket set and a torque wrench will certainly do the trick. Just in case you're not that fortunate, it's probably best to prepare yourself for some resistance. So make sure you have some penetrating oil, a sledgehammer, a hacksaw or an acetylene torch on hand.

There are dozens of factors that can complicate your brake conversion -- all depending on the make, model and year of your vehicle. You may need to remove springs, shocks, and possibly even an axle in order to get this job done, so make sure you know what you're in for before you get too far in the process.

As for putting the new brakes on, conversion kits have everything you'll need to put your new brakes together, but if you're shopping at the local junkyard, you'll be taking brakes off the donor car in addition to your own, so ­make sure you're tooled-up for another possible struggle.

Front- and rear-brake assemblies are not interchangeable, so front and rear conversions do differ slightly. Read on to find out what's required for each, and what complications you may encounter.

If you're doing a front disc brake conversion, you're probably working on an older vehicle. This may mean that you will have to do more than simply replace the old brakes.

Removing the Drum Brakes

Not all d­rum brakes are created equal, but they're all similar enough that removing them follows the same basic steps. Start by removing the wheels and tires. Next, you will need to take off the dust cap, and then remove the center nut, washer and brake-drum bolts.

Disconnect the brake hose before you remove the drum, and once you've taken the drum off, you should inspect the spindle. If the spindle is worn or rusted, you should replace it. But if it looks good, you can clean it up and reuse it. Now just reposition and secure the steering arm and you're halfway to the finish line.­

Installing the Disc Brakes

Some brake conversion kits come pre-assembled, but assuming yours isn't, or if you're using recycled parts, here's how you can assemble your disc brakes. Attach the rotor to the spindle and then put on the bearing and nut, the washer and the cotter pin. Now put on the dust cap, and then you can move on to the caliper assembly.

Before you put the caliper on the rotor, attach the new brake lines and install the pads. Then you can put the caliper in position over the rotor, reattach the brake lines and then back go the wheels and tires.

After you've finished the conversion, you will need to bleed the brakesand refresh the brake fluid. Bleeding the brakes will flush out any air that's gotten into the brake line. And since you've disconnected those lines, there will be air inside. This can cause your brakes to feel spongy or can make your pedal dip close to the floor.­

Removing The Drum Brakes

Rear drum removal is essentially the same as removing front drums, except for that pesky parking brake. Start by removing the wheels and then the dust cap, the center nut and washer and the brake-drum bolts. Before you remove the drum, you need to disconnect the brake hose and parking brake cable. After you remove the drum, inspect the spindle and either replace it or reuse it. Then reposition and secure the steering arm.

Installing The Disc Brakes

Attach the rotor to the spindle, followed by the washer, the bearing and nut and the cotter pin. Then put the dust cap on and move on to the caliper assembly.­

Before positioning the caliper on the rotor, attach the new brake lines and install the pads. Then place the caliper over the rotor and attach the parking brake and the brake lines. Put the wheels and tires back on and you're nearly done.

As with the front conversion, it's extremely important to bleed the brakes and refresh the brake fluid. Equally important is testing the parking brake and making necessary adjustments.

One reason automakers favor a front-disc/rear-drum configuration (aside from the low cost), is that drum brakes require a simpler -- and cheaper -- mechanism to operate the parking brake. On drum brakes, the parking brake cable controls a lever that's connected to the brake shoes. With disc brakes, the lever attaches to a separate mechanical device inside the caliper piston that pushes the piston into the pads. On some cars, the lever attaches to a separate drum inside the rear brake rotor, depending on single-piston or four-piston calipers brakes.

What this means for your conversion is that, depending on your vehicle, you may need to install an entirely new parking brake system. If you're lucky and your new brakes are compatible with your parking brake system, all you'll need to do is disconnect the parking brake before removing the old brakes, and then reconnect it after you've installed the new ones.