[Catalog:News] [Date:2020-3-4] [Hits:] [Return]

Other Components in the Hydraulic System

Proportioning Valve or Equalizer Valve

These valves are mounted between the master cylinder and the rear wheels. They are designed to adjust the pressure between the front and rear brakes depending on how hard you are stopping. The shorter you stop, the more of the vehicle’s weight is transferred to the front wheels, in some cases, causing the rear to lift and the front to dive. These valves are designed to direct more pressure to the front and less pressure to the rear the harder you stop. This minimizes the chance of premature lockup at the rear wheels.

Pressure Differential Valve

This valve is usually mounted just below the master cylinder and is responsible for turning the brake warning light on when it detects a malfunction. It measures the pressure from the two sections of the master cylinder and compares them. Since it is mounted ahead of the proportioning or equalizer valve, the two pressures it detects should be equal. If it detects a difference, it means that there is probably a brake fluid leak somewhere in the system.

Combination Valve

The Combination valve is simply a proportioning valve and a pressure differential valve that is combined into one unit.

Electronic Brake Force Distribution

Newer cars use the antilock brake hardware and the onboard computer to replace these proportioning valve systems with a system called Electronic Brake force Distribution (EBD) in order to distribute the exact amount of pressure at each wheel to insure a balanced brake system.

Disk Brakes

The disk brake is the best brake we have found so far. Disk brakes are used to stop everything from cars to locomotives and jumbo jets. Disk brakes wear longer, are less affected by water, are self adjusting, self cleaning, less prone to grabbing or pulling and stop better than any other system around. The main components of a disk brake are the Brake Pads, Rotor, Caliper and Caliper Support.

Brake Pads

There are two brake pads on each caliper. They are constructed of a metal “shoe” with the lining riveted or bonded to it. The pads are mounted in the caliper, one on each side of the rotor. Brake linings used to be made primarily of asbestos because of its heat absorbing properties and quiet operation; however, due to health risks, asbestos has been outlawed, so new materials are now being used. Brake pads wear out with use and must be replaced periodically. There are many types and qualities of pads available. The differences have to do with brake life (how long the new pads will last) and noise (how quiet they are when you step on the brake). Harder linings tend to last longer and stop better under heavy use but they may produce an irritating squeal when they are applied. Technicians that work on brakes usually have a favorite pad that gives a good compromise that their customers can live with. Brake pads should be checked for wear periodically. If the lining wears down to the metal brake shoe, then you will have a “Metal-to-Metal” condition where the shoe rubs directly against the rotor causing severe damage and loss of braking efficiency. Some brake pads come with a “brake warning sensor” that will emit a squealing noise when the pads are worn to a point where they should be changed. This noise will usually be heard when your foot is off the brake and disappear when you step on the brake. If you hear this noise, have your brakes checked as soon as possible.

Rotor

The disk rotor is made of iron with highly machined surfaces where the brake pads contact it. Just as the brake pads wear out over time, the rotor also undergoes some wear, usually in the form of ridges and groves where the brake pad rubs against it. This wear pattern exactly matches the wear pattern of the pads as they seat themselves to the rotor. When the pads are replaced, the rotor must be machined smooth to allow the new pads to have an even contact surface to work with. Only a small amount of material can be machined off of a rotor before it becomes unusable and must be replaced. A minimum thickness measurement is stamped on every rotor and the technician doing the brake job will measure the rotor before and after machining it to make sure it doesn’t go below the legal minimum. If a rotor is cut below the minimum, it will not be able to handle the high heat that brakes normally generate. This will cause the brakes to “fade,” greatly reducing their effectiveness to a point where you may not be able to stop!

Caliper & Support

There are two main types of calipers: Floating calipers and fixed calipers. There are other configurations but these are the most popular. Calipers must be rebuilt or replaced if they show signs of leaking brake fluid